Step-by-Step Instructions

INSTRUCTIONS FOR AQUASEAL CRÈME

• DO NOT HEAT.
• Rub in with fingers.
• For very dry leather or extreme wet conditions, apply a second coat.
• Initial application on new leather should be 2 or 3 coats.
CAUTION:
Some darkening of leather will occur.
Will darken and flatten the nap on suede leather.
For fine leathers try on a hidden spot first.

INSTRUCTIONS FOR AQUASEAL LIQUID W/DAUBER

1. Shake well before using.
2. Apply LIQUID AQUASEAL, with the dauber, to all leather and fabric areas. For very dry leather, 1 or 2 more coats may be necessary for maximum protections.
3. On smooth leather, a haze will form when the AQUASEAL dries (usually about one hour), lightly polish this haze until it shines.
4. Reapply LIQUID AQUASEAL at regular intervals depending on severity of usage, usually twice a month.


CAUTION:
Some darkening of leather will occur. For fine leathers try on a hidden part first.

INSTRUCTIONS FOR AQUASEAL LIQUID W/PUMP

• Clean footwear thoroughly.
• Apply at room temperature in well-ventilated area.
• Shake well and prime pump with a few slow pumps.
• Holding bottle upright about 6" from footwear, spray with sweeping motion to evenly comer entire surface.
• Daub streaks and runs, if any, with a clean dry cloth.


For best results, let dry for 24 hours. Apply more frequently during wet weather. Do not over apply, 1-2 coats is all that is needed. If a light haze appears brush lightly or go over lightly with a hair dryer. Some darkening of leather may occur. Test for color fastness before using.

INSTRUCTIONS FOR AQUASEAL FOR SUEDE & NUBUCK

• Clean footwear thoroughly.
• Apply at room temperature in well-ventilated area.
• Shake well and prime pump with a few slow pumps.
• Holding bottle upright about 6" from footwear, spray with sweeping motion to evenly comer entire surface.
• Daub streaks and runs, if any, with a clean dry cloth.


For best results, let dry for 24 hours. Apply more frequently during wet weather. Do not over apply, 1-2 coats is all that is needed. If a light haze appears brush lightly or go over lightly with a hair dryer. Some darkening of leather may occur. Test for color fastness before using.

INSTRUCTIONS FOR STITCH GUARD

• Boots must be clean and dry, especially stitching.
• Snip off applicator, keep hole small.
• Apply 2 coats to sole, one to other stitches.
• Wait 15 to 30 minutes between coats but no longer than 45 minutes .
• Apply directly to threads and stitch holes. Plug each stitch hole and coat all exposed stitching thread.
• A light squeeze pressure to the applicator bottle is all that is needed.
• If puddling occurs, absorb excess w/ paper towel.
• Clean runs immediately w/ damp sponge.
• Allow 24 hrs. dry/cure time.

INSTRUCTIONS FOR AQUASEAL ALL-PURPOSE FOOTWEAR CLEANER

1. Remove laces and dry brush the entire shoe/boot.
   Remove all loose particles and soil.
2. Dilute 1 tablespoon of FOOTWEAR CLEANER into approximately 1 gallon of water.
   Wet the brush with soap solution and scrub wetted footwear thoroughly (working up a lather).
   Insides should be scrubbed with a cloth or sponge.
   Note: For especially soiled articles (grease, mud, etc.) use 2 tablespoons of FOOTWEAR CLEANER per gallon of water.
3. Rinse thoroughly under running water. Check for spots that may have been missed. Spot scrub as necessary. Rinse and dry.
4. Dry in direct sunlight if possible, or in heat comfortable to your own skin.
5. For lasting results, apply Liquid Aquaseal, Aquaseal Crème or Aquaseal Suede & Nubuck to waterproof and condition your footwear.

INSTRUCTIONS FOR AQUASEAL SHOE & BOOT LEATHER CARE KIT

PREPARATION: Before use, check for color fastness in an inconspicuous area. Remove laces and dry brush the entire boot/shoe/article with a stiff bristle brush. Remove all loose particles and soil. Wet shoes, laces and insoles with cold water.

CLEAN: Dilute 1 tablespoon of Tech Care Cleaner into approximately ½ gallon of water. Wet bristle brush with soap solution and scrub wet footwear thoroughly, working up a lather. Scrub insides with cloth or sponge. For especially soiled articles (grease, mud, etc.) use 2 tablespoons of Tech Care Cleaner per ½ gallon of water.

RINSE: Rinse thoroughly under running water. Check for spots that may have been missed. Spot scrub as necessary to remove any leftover soil.

LET DRY: Dry in direct sunlight if possible, or in heat comfortable to your own skin. Temperature should not exceed 120 F. Excessive heat may damage shoes or boots.

SEAL STITCHES: apply 2 coats of Stitch Guard to the sole stitching, 1 coat to the other stitches. Wait 10-15 minutes between coats, no longer than 30 minutes. Apply directly to exposed stitching threads and into stitch holes. Clean runs immediately.

WATERPROOF: Once dry, apply Aquaseal Paste waterproofing and conditioner to help seal and condition the leather portion of your footwear. Aquaseal protects your footwear investment from the harmful effects of moisture and dirt.

INSTRUCTIONS FOR AQUASEAL CORK SEAL

Be sure cork is clean. Brisk, dry brushing and/or light sanding is usually adequate. Holding sandals right side up, apply one generous coat to exposed cork edges, sides, etc., taking care to avoid leather uppers. Do not allow runs. Dry for 3 hours before using. Clean all spills immediately with damp cloth.

• Waterproofs the cork
• Helps prevent chipping and abrading
• Greatly increases usable life of the cork
• Enhances the appearance of cork.

INSTRUCTIONS FOR AQUASEAL BLACK LEATHER

1. Clean leather thoroughly
2. Shake well before using.
3. Apply BLACK LEATHER , with the dauber, to all leather areas. For very dry leather or extremely wet conditions, a second coat may be necessary for maximum protection. Allow 24 hrs. dry/ cure time before use.
4. On a smooth leather, a haze may form when BLACK LEATHER dries, (usually about one hour.); lightly buff this haze until it shines. If a white residue appears, go over quickly with a hair dryer; it will dissipate instantly.
5. Re-apply BLACK LEATHER at regular intervals depending on the frequency and serverity of usage.


IMPORTANT !
Test for color uniformity on a hidden spot; will flatten the nap on suede and nubuck.

INSTRUCTIONS FOR AQUASEAL MAP SEAL

• Shake or stir gently before using.
• Spread map flat.
• Very briskly daub on MAP SEAL with dauber working it into the paper, applying evenly.
• Hang to dry.
• In about 5 minutes, or when fluid is noticeably tacky, repeat the procedure.
• When dry (about 30-min.) coat the other side the same way.
• Do not allow the coated surfaces to touch each other or other objects while wet.
• Allow 72 hours cure time before using map.
• Do not allow dauber to dry out.
• 4oz. of MAP SEAL will coat approximately 3-4 topo maps, front and back.
• For extra mileage daub on quickly using thin coats.


IMPORTANT!
Always store coated maps loosely in a breathable NON-airtight enclosure.

INSTRUCTIONS FOR AQUASEAL POLY COAT

• Apply in well-ventilated area. Before using, shake or stir gently until white color on top is dispersed.
• All surfaces to be coated must be clean and dry. Wash thoroughly and remove loose particles. Rinse thoroughly, all traces of cleaner must be removed. WARNING: Machine washing of polymer coated nylons may loosen the old coating to such a degree that it may have to be removed prior to applying POLYCOAT.
• When applying to coated fabrics, always apply to the side opposite from that which is coated. The existing coat will tend to peel if POLYCOAT is applied to it. This makes it appear as though the POLYCOAT is peeling, apply to the opposite side only.
• Use a medium bristle brush, flow on evenly and spread out preventing runs. Allow to dry for a few minutes, then brush out all runs and puddles. If runs and puddles are allowed to dry hard, the film may peel in that area. Material soaks through fabric, be sure opposite side is free and clear during application. Dry 72 hours at 70 F prior to folding. Sprinkle talcum powder on coated areas prior to folding the first time. One application is all that is necessary.
• Heavy traffic areas (such as tent floors) need two coats. If there is not existing coating on the floor (not very likely), both sides may be coated. If both coats are applied to the same side, apply second coat while first coat is still tacky, i.e., 5-15 minutes air dry.
• Keep brush wet at all times then clean promptly with water. Keep container tightly capped when not in use.
CAUTION:
POLYCOAT is a utility product designed for restoring waterproofing, it may change the aesthetic appearance of the fabric it is applied to.

INSTRUCTIONS FOR AQUASEAL SEAM SEAL (Solvent-based)

• Remove all dirt and oil from seams.
• Daub on one coat of SEAM SEAL with the dauber cap on the container.
  The dauber is especially useful on double stitched seams where both seams can be sealed simultaneously.
  A wiping motion will help deposit the sealant in all seams, stitching holes, thread and fabric joints.
  Always seal on the inside whenever practical.
  Will leave noticeable coating.
• Dry about 1 hour. Repeat.

INSTRUCTIONS FOR AQUASEAL SEAM SEAL, (WATER-BASED)

• Remove all dirt from seams. Heavily soiled seams should be dry brushed with a stiff bristle brush. If necessary use Seam Prep to assist in cleaning.
• Apply SEAM SEAL with the applicator provided.
  Daub on one coat with the dauber cap on the container.
  The dauber is especially useful on double stitched seams where both seams can be sealed simultaneously.
  A wiping motion will help deposit the sealant in all seams, stitching holes, thread and fabric joints.
  Seal garment, tent and pack seams from inside whenever possible. Will leave noticeable coating.
• Dry at room temperature for two hours before folding or using.
  One coat does the job.